|
|
9-3-snyatie-i-ustanovka-at-i-gidrotransformatora.html
9.3. Removal and AT installation and hydrotransformerRemoval
|
Below the description on an example of AT A5S 310Z of the M60/1 engine is provided. |
|
- Disconnect a negative wire from the storage battery.
- Remove system of release of OG assembled, and also its thermofilters (see. Head of the Power supply system and production of the fulfilled gases).
- Remove arms of fastening of mudguards from both parties.
|
- On models to 08.1995 g вып. establish the selector lever in the situation "P" and establish the adaptation No. 24 5 240 on the control unit balance weight. Give a nut (1).
|
|
At installation adjust the selector lever. |
|
- On models from 08.1995 g вып. give a nut (2, holding a clip (1).
|
|
At installation adjust the selector lever. |
|
- Take out a screw-driver a clamp (1) and pull out draft (2).
|
|
- Remove the thermofilter on the left side of a beam of the forward bridge. Disconnect arms of fastening of oil pipelines from an engine case.
|
|
- Substitute capacity for collecting following oil, give fixture (1) and liberate tips of oil pipelines from AT case.
|
|
At assembly use new sealing rings of oil pipelines. |
|
- Prop up AT by means of the No. No. 00 2 030/24 5 300 special adaptations.
|
- Disconnect the driveshaft from AT and hang out it (see. Head Kardanny and power shafts, reducer, differential and stupichny assemblies).
|
- Separate sockets of electroconducting and take it from fastening brackets to AT case.
|
|
- Special key No. 24 1 110 verify 4 bolts of fastening of the hydrotransformer.
|
|
- Turn out a bolt and take away down a cover of a wire of a positive conclusion of the storage battery.
|
- Insert the adaptation (whetstone) No. 23 3 030 between the pallet of a case of the engine and a beam of the forward bridge.
- To turn to the left forward wheels and lower AT.
|
- To prevent a vyskalzyvaniye of the hydrotransformer fix it concerning AT. For this purpose insert the adaptation No. 24 4 080 into a window (1) case of AT and hold them the hydrotransformer.
|
|
- Turn out bolts of fastening of AT, take away it back, pull out and lower AT.
|
|
- If necessary remove the hydrotransformer. For this purpose screw in it adaptations No. 24 4 000 and take out the hydrotransformer from AT.
|
|
|
Installation
|
- Installation is made upside-down. Pay attention to the next moments.
- At installation of the hydrotransformer do not allow damage of a sealing ring and the bearing. To insert the hydrotransformer into a case, slightly press on it and turn until dredging of the hydrotransformer will be not included into gearing with a power shaft of the oil pump. Press the hydrotransformer against the stop.
- To roll bolts of fastening of AT follows only together with washers.
|
- At AT installation the adaptation No. 24 2 300 should settle down coaxially to openings in the compensating coupling, and through a window of the pallet of a case there should be an access to an opening (1) compensating coupling. Screw the adaptation No. 24 2 300 in a carving opening and if necessary turn the hydrotransformer so that this opening appeared below.
|
- Be convinced available centering plugs. If necessary, take out centering plugs from a case of AT and insert into the block of cylinders. The damaged centering plugs replace.
- Upon termination of works check level of ATF and if necessary modify it (see. Head of Control and routine maintenance of the car).
|
|
|
|
|