BMW 7_ая the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
5. Systems of cooling of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
8.1. Manual box of gear shifting
8.1.1. General information
8.1.2. Removal and RKPP installation
8.1.3. Removal and installation of components of a drive of gear shifting
8.1.4. Major maintenance of a transmission
8.2. Coupling
9. Automatic transmission
10. Kardanny and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
14. Onboard electric equipment
15. Electric equipment schemes




0c1943ba

8-1-2-snyatie-i-ustanovka-rkpp.html

8.1.2. Removal and RKPP installation

Below the description for RKPP S5D 310Z is provided.


 PERFORMANCE ORDER

  1. Disconnect a negative wire from the storage battery.
  2. Remove assembly of system of release of OG and its thermofilters (see. Head of the Power supply system and production of the fulfilled gases).
  3. Disconnect electroconducting a lambda probes from a cross-piece of a stretcher and from RKPP.
  1. Separate the socket of electroconducting Д/В of lamps of a backing. Disconnect electroconducting from a cross-piece of a stretcher and from RKPP.
  1. On the M62 engine remove the CKP sensor (see. Head of System of electric equipment of the engine).
  1. Disconnect the driveshaft from RKPP and hang out it. Prop up RKPP a jack. Turn out bolts and remove a frame cross-piece.
  1. On models with M51, M52, M60 and M62 engines lay between the pallet of a case of the engine and a beam of the forward bridge whetstone (the adaptation No. 23 3 030, – for M60 and M62 engines, or No. 11 7 360, – for M51 and M52 engines). On models with M60 and M62 engines turn forward wheels to the left against the stop and lower a transmission.
  1. Remove a clamp (4), take out draft of a drive of gear shifting from the hinge and remove washers (5).

At installation grease draft of a drive of gear shifting.


  1. Screw-driver lift up a lock bracket. Take out an axial finger of a lock bracket and remove a core of a support of the lever of gear shifting.

At installation grease fingers.

  1. Remove the executive cylinder of a hydraulic actuator of coupling, without disconnecting the pressure head pipeline.

Depression in the executive cylinder should be dumped gradually that through a sealing cuff in the cylinder air was not soaked up.


  1. Prop up RKPP a jack, turn out bolts of its fastening, allocate for RKPP back and remove movement down.

At removal and RKPP installation should not hang on entrance to a shaft, the conducted disk of coupling otherwise can be deformed. At installation roll fastening bolts only together with washers!

  1. Installation is made upside-down. To pay attention to aligning plugs: if necessary take out them from a case of RKPP and insert into the block of cylinders. The damaged aligning plugs replace. Remove the coupling and a fork of switching off of coupling, clear them and grease in the corresponding places. If greasing on entrance to RKPP shaft sticky to replace a conducted disk of coupling.
  2. Having used a case, check a conducted disk of coupling on lack of a rust in shlitsa and if necessary replace a disk. By means of rags remove from shliyets of a conducted disk of coupling old greasing and a dust formed at an istiraniye of a frictional slip. After that with a brush evenly put greasing for shlitsevy connections by a thin layer on all surface of shliyets, on shlitsevy a groove and a neck.
  3. After installation pump over a coupling hydraulic actuator, modify level of transmission liquid and make sure of absence of its leaks.


«previous page
8.1.1. General information
following page»
8.1.3. Removal and installation of components of a drive of gear shifting