BMW 7_ая the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
5. Systems of cooling of the engine, heating, ventilation and air conditioning
5.1. System of cooling of the engine
5.2. Systems of heating, ventilation and air conditioning
5.2.1. General information
5.2.2. Removal and heater installation
5.2.3. Removal and installation of a radiator of a heater
5.2.4. Removal and installation of fans and rezistorny assemblies
5.2.5. Removal and installation of the additional water pump and water valve
5.2.6. Removal and installation of deflectors of systems of heating, ventilation and To/in
5.2.7. Removal and To/in compressor installation
5.2.8. Removal of other components of To/in system
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Kardanny and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
14. Onboard electric equipment
15. Electric equipment schemes




0c1943ba

5-2-1-obshhaya-informaciya.html

5.2.6. Removal and installation of deflectors of systems of heating, ventilation and To/in

Lateral deflectors

PERFORMANCE ORDER

Before removal of the left deflector execute the following actions: Remove a wooden level and separate the socket of switches of illumination of the dashboard and adjustment of an inclination of headlights; the Wooden level Turn out top (without a prokladochny washer) and bottom (with a prokladochny washer) bolts of fastening and remove the left ware box.

Unhook a cable of an unblocking of the parking brake. Fixture of the left ware box Before removal of the right deflector execute the following actions: Open and incline down a ware box. Turn out screws and unbend the top part of facing of a ware box; Clamps of the left lateral deflector Separate sockets of the switch and a lamp of illumination of a ware box and remove facing.

Close the deflector. Take away sound insulation (1) a little down to provide access to both clamps of the deflector. Wring out at first one, then the second clamp of the deflector. That the wrung-out clamp was not blocked, establish between the bottom edge of the deflector and its nest a thin wide plate (adaptation No. 00 9 300). Separate from the deflector a sleeve of supply of air. Top and the central deflectors At removal of deflectors of models with the integrated system of heating and To/in pass to paragraph 6. In paragraphs with 1 on 5 preparatory operations at removal of deflectors of models with К/В system adjustment are described.

ORDER of PERFORMANCE Turn out the screw (1), raise the panel of facing (2) foot wells of the forward passenger a little and remove it movement on itself (3). Turn out bolts (1) and take out rivets (2 and 3) fastenings of the bottom panel of the right ware box. Delay facing forward, remove and separate the buzzer socket. Open and incline down a ware box. Turn out screws and unbend the top part of facing of a ware box (see an illustration). Separate sockets of the switch and a lamp of illumination of a ware box and remove facing.

Take out rivets, movement up separate the socket and remove lateral facing panels. Take out from fastenings an air line in a foot well. Unhook a cable of a drive of a zaslonka of adjustment of air temperature. Enter the adaptation No. 00 9 300 between the top deflector (1) and a frame (2). Consistently unclench clamps of the top lattice in points (1-3), pick up and remove a lattice. Turn out screws. Pick up and remove a frame snuffled ventilation, separate To the/l socket (1). Turn out the screw (1) and take out a pro-rate (2).

Close the deflector, wring out it a little up and enter both adaptations No. 00 9 300 below into a crack between the deflector and the dashboard so to wring out clamps (1). Similarly wring out the top clamps. Push both hands in an aperture of the top deflector and вытолкните the central deflectors from within. Installation is made upside-down. The deflector in a back part of salon Depending on a complete set under the deflector can be established the control panel by a heater or a decorative level.

In any case removal of the deflector is made equally. The PERFORMANCE ORDER wring out from each other the deflector (1) and the control panel a heater (2) A little. Wring out clamps and deduce the control panel a heater at first from the top directing groove, then delay the deflector up and remove the control panel. Displace the deflector down on size about 35 mm and deduce from deepenings in directing grooves.

For installation get the deflector (1) in deepenings in the middle of directing grooves and insert up to the end movement up. After that establish a decorative level or the control panel a heater.


«previous page
5.2.5. Removal and installation of the additional water pump and water valve
following page»
5.2.7. Removal and To/in compressor installation