BMW 7_ая the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
4.1. General information and preparatory operations
4.2. Check of kompressionny pressure
4.3. Engine check by means of the vacuum gage
4.4. Petrol M60/1 and M60/2 engines
4.5. M62 engine
4.6. Diesel M57 engine
4.7. Diesel M67 engine
4.7.1. Removal and installation of a cover of a head of cylinders
4.7.2. Removal and installation of heads of cylinders
4.7.3. Removal and installation of the top section of the pallet of a case
4.7.4. Removal and installation of the pallet of a case
4.7.5. Replacement of epiploons of a cranked shaft
4.7.6. Replacement of an oil separator of PCV system
4.7.7. Removal and flywheel installation
4.7.8. Removal and installation of a damper of krutilny fluctuations
4.7.9. Removal and installation of driving belts and their natyazhitel
4.7.10. Removal and installation of the oil pump
4.7.11. Removal and installation of maslookhladitel
4.7.12. Removal and installation of the inlet pipeline
4.7.13. Removal and installation of final collectors
4.7.14. Removal and installation of the vacuum pump
4.7.15. Removal and engine installation
5. Systems of cooling of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Kardanny and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
14. Onboard electric equipment
15. Electric equipment schemes




0c1943ba

4-7-9-snyatie-i-ustanovka-privodnykh-remnejj-i-ikh-natyazhitelejj.html

4.7.9. Removal and installation of driving belts and their natyazhitel

Driving belts

For removal of a belt of a drive of the To/in compressor the belt of a drive of the generator should be removed. If further use of a removed belt is supposed, note the direction of its movement.


 PERFORMANCE ORDER

  1. Remember the scheme of laying of belts on pulleys.
  1. Give a cap nut (1) krylchatka of the fan of system of cooling, trying not to damage a radiator.
  1. Wring out a natyazhitel of a driving belt for a shestigrannik (1) in the direction of an arrow and remove a driving belt (2).
Removal of a belt of a drive of the To/in compressor
  1. Check a belt condition (see. Head of Control and routine maintenance of the car) and if necessary replace it.
  2. Lay a driving belt on pulleys and rollers and make sure of correctness of its situation.

At installation of already used belt observe the former direction of its movement.

Natyazhiteli

 PERFORMANCE ORDER

  1. Remove a belt of a drive of the generator.
  2. Remove a casing of the fan of system of cooling (see. Head of System of cooling of the engine, heating, ventilation and conditioning).
  1. Uncover (1) bolt and turn out it. Turn out a bolt (2) on a damper.
  1. Turn out the screw and take out a damper from the holder.
  1. Remove a belt of a drive of the К/В compressor.
  1. Turn out bolts (1 and 2) and remove a damper. Turn out a bolt (3) and remove a natyazhitel.


«previous page
4.7.8. Removal and installation of a damper of krutilny fluctuations
following page»
4.7.10. Removal and installation of the oil pump