BMW 7_ая the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
4.1. General information and preparatory operations
4.2. Check of kompressionny pressure
4.3. Engine check by means of the vacuum gage
4.4. Petrol M60/1 and M60/2 engines
4.5. M62 engine
4.6. Diesel M57 engine
4.7. Diesel M67 engine
4.7.1. Removal and installation of a cover of a head of cylinders
4.7.2. Removal and installation of heads of cylinders
4.7.3. Removal and installation of the top section of the pallet of a case
4.7.4. Removal and installation of the pallet of a case
4.7.5. Replacement of epiploons of a cranked shaft
4.7.6. Replacement of an oil separator of PCV system
4.7.7. Removal and flywheel installation
4.7.8. Removal and installation of a damper of krutilny fluctuations
4.7.9. Removal and installation of driving belts and their natyazhitel
4.7.10. Removal and installation of the oil pump
4.7.11. Removal and installation of maslookhladitel
4.7.12. Removal and installation of the inlet pipeline
4.7.13. Removal and installation of final collectors
4.7.14. Removal and installation of the vacuum pump
4.7.15. Removal and engine installation
5. Systems of cooling of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Kardanny and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
14. Onboard electric equipment
15. Electric equipment schemes


4-7-3-snyatie-i-ustanovka-verkhnejj-sekcii-poddona-kartera.html

4.7.3. Removal and installation of the top section of the pallet of a case

 PERFORMANCE ORDER

  1. Establish a steering wheel in the situation corresponding to rectilinear movement of the car.
  2. Remove back facing of the bottom of a body.
  3. Remove the top cover of the engine.
  1. Holding a cowl, separate from it both holding racks.
  1. Bring a cowl into vertical situation and fix it, having screwed in loops two bolts М8.
  1. By means of the elevating adaptation hang out the engine for forward and back elevating eyes so to unload a beam of the forward bridge.
  2. Remove a casing of the fan of system of cooling.
  1. Turn out a bolt (1) and disconnect the pipeline (2) GUR.

Collect following GUR liquid. If necessary replace sealing rings of the pipeline.

  1. Remove the bottom section of the pallet of a case (see. Section Removal and installation of the pallet of a case).
  1. Weaken collars (1) drain oil pipeline and take away a hose (2) back.
  1. Turn out bolts (1), unclench a clip (2) and remove the thermofilter (3).
  1. Turn out bolts (1), disconnect a positive wire (2) battery rooms of the battery together with a flange from a beam of the bridge and tie up behind.
  1. Execute the actions described in paragraphs from 10 on 18 Section Removal and installation of the top section of the pallet of a case.
  2. Disconnect a steering shaft from the steering mechanism (see. Head Suspension bracket and steering).

In order to avoid damage of a spiral spring to a steering column upon termination of its works it is necessary to center surely.


  1. Give nuts of the left and right pillows of support of the engine.
  1. Turn out a bolt (1) on AT and disconnect pipelines (2) ATF.

If necessary replace sealing rings of pipelines.

  1. Prop up a beam of the forward bridge by means of the hydraulic lift, turn out bolts of its fastening and lower a beam as it is possible below (see. Head Suspension bracket and steering).
  1. Turn out bolts (1) on a case of a transmission and all bolts (2) top sections of the pallet of a case.

At installation pay attention to the various moments of a tightening of bolts of M6 and M8. Use new laying of the top section of the pallet of a case.


  1. In case of replacement of the top section of the pallet of a case it is necessary to rearrange whenever possible a partition (2) from the old pallet on the new.
  1. Installation is made upside-down. Pay attention to the next moments:
    • Put on an interfaced surface between a cover of a back epiploon of a cranked shaft and an engine case a strip (2 mm in height and 3 mm in width) Drei Bond 1209 hermetic;
    • Greasing by oil laying of the top section of the pallet of a case is not allowed. Use new laying;
    • Bolts tighten in a cross order.


«previous page
4.7.2. Removal and installation of heads of cylinders
following page»
4.7.4. Removal and installation of the pallet of a case