BMW 7_ая the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
4.1. General information and preparatory operations
4.2. Check of kompressionny pressure
4.3. Engine check by means of the vacuum gage
4.4. Petrol M60/1 and M60/2 engines
4.5. M62 engine
4.5.1. Removal and installation of covers of heads of cylinders
4.5.2. Removal and installation of heads of the block of cylinders
4.5.3. Removal and installation of the top section of the pallet of a case and oil pump
4.5.4. Removal and installation of the pallet of a case
4.5.5. Removal and installation of covers of a chain of GRM
4.5.6. Replacement of epiploons of a cranked shaft and consolidations of distributors of ignition
4.5.7. Removal and flywheel installation
4.5.8. Removal and installation of a damper of krutilny fluctuations
4.5.9. Removal and installation of driving belts
4.5.10. Removal and installation of the oil pump
4.5.11. Removal and installation of inlet pipelines
4.5.12. Removal and installation of final collectors
4.5.13. Removal and engine installation
4.6. Diesel M57 engine
4.7. Diesel M67 engine
5. Systems of cooling of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Kardanny and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
14. Onboard electric equipment
15. Electric equipment schemes




0c1943ba

4-5-3-snyatie-i-ustanovka-verkhnejj-sekcii-poddona-kartera-i-maslyanogo-nasosa.html

4.5.3. Removal and installation of the top section of the pallet of a case and oil pump

For removal of an oil case it is required to lower a beam of the forward bridge.


 PERFORMANCE ORDER

  1. Execute the actions described in paragraphs from 10 on 13 Section Removal and installation of the top section of the pallet of a case.
  2. Give the top nuts of the left and right pillows of support of the engine (see an illustration).
  3. Hang out the engine on 6 ÷ 8 mm by means of the special adaptation, using elevating eyes of the engine.
  4. Remove directing щупа level of impellent oil.
  5. Remove the case pallet (see. Section Removal and installation of the pallet of a case).
  6. Weaken a tension of a belt of a drive of the To/in compressor and remove from a case a level of a natyazhitel (see. Section Removal and installation of driving belts).
  1. Turn out a bolt and unclench a collar of fastening of the pipeline to the pump GUR.
 
  1. Without disconnecting a tube, remove the pump GUR and suspend it aside so that pipelines were not loaded.

If necessary turn out from the top part of a case an adjusting pin.


  1. Give fixture of a positive wire on the generator (2).
  1. Turn out a bolt of a fixing bracket of a positive wire on an engine support.
  1. Turn out bolts and remove from a case a protective tube.
  1. Turn out bolts of fastening of a fixing plate to a beam of the forward bridge, unclench brackets and lift the receiver also a plate.
  1. Remove the thermofilter.
  1. Remove a positive wire from an engine case.
  1. Remove the returnable pipeline of impellent oil from a case by means of the special adaptation.
  1. Disconnect a steering shaft from the steering mechanism (see. Head Suspension bracket and steering).
  2. Prop up a beam of the forward bridge, disconnect it from a support of the engine and lower approximately on 60 mm.
  1. Turn out bolts in the top section of the pallet of a case and remove the oil pump.
  1. Turn out bolts of fastening of the top section of the pallet of a case from transmission (see an illustration).
  2. Turn out the remained bolts of fastening of the top section of the pallet of a case and remove it in the direction forward.
  3. Installation is made upside-down. Pay attention to the next moments:
    • If necessary replace sealing rings directing щупа level of impellent oil;
    • Clear interfaced surfaces of the remains of sealing materials and grease these surfaces with Hylomar SQ 32 hermetic M;
    • Replace laying of the top section of the pallet of a case;
    • Finally to tighten bolts from transmission follows only after a tightening of bolts from the engine.


«previous page
4.5.2. Removal and installation of heads of the block of cylinders
following page»
4.5.4. Removal and installation of the pallet of a case