BMW 7_ая the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
5. Systems of cooling of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Kardanny and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
14. Onboard electric equipment
14.1. General information, diagnostics of malfunctions
14.2. Lighting devices
14.2.1. Adjustment of headlights
14.2.2. Removal and installation of headlights and their components
14.2.3. Removal and installation of other devices of external lighting
14.2.4. Removal and installation of devices of internal lighting
14.2.5. Replacement of lamps of devices of external lighting
14.2.6. Replacement of lamps of devices of internal lighting
14.3. Screen wipers and washers
14.4. Other electric equipment
15. Electric equipment schemes




0c1943ba

14-2-5-zamena-lamp-priborov-naruzhnogo-osveshheniya.html

14.2.5. Replacement of lamps of devices of external lighting

It is necessary to replace filament lamps only with lamps of the same type. Before replacement of a lamp check, that the corresponding light device was switched off. Do not take a filament lamp flask naked fingers, use a pure towel or cotton gloves. The fingerprints left on a flask of a lamp, evaporate and besieged on a reflector that is especially appreciable on headlights and fog lights. It is necessary to remove casually left fingerprints with a napkin impregnated with alcohol. It is not allowed to wipe the reflectors of headlights covered with a protective varnish, a dry rigid rag, and also to apply to this purpose any cleaners or solvents. Use soft damp napkins.

Halogen lamps are under pressure and can burst. Therefore at their replacement it is necessary to use goggles and gloves. At replacement of xenon lamps there is a danger of a travmirovaniye owing to a high voltage! Surely switch off headlights and disconnect electroconducting from the battery. After replacement quickly switch on and off a headlight to remove residual stress. As a security measure put on boots with rubber soles.

Headlight lamps (parking, near and far light)

 PERFORMANCE ORDER

  1. Wring out clamps down and remove covers of lamps.
  1. Separate the corresponding socket, remove a spring bracket and take out a lamp.
1 — the Passing beam
2 — the Driving beam
3 — the Parking light

For removal of a lamp of a parking light remove a cartridge and turn a lamp.

Lamp of a xenon headlight

 PERFORMANCE ORDER

  1. Liberate a clip and uncover lamps.
  1. Separate the lamp socket, remove a spring bracket and take out a lamp.

Halogen lamp of a fog light

 PERFORMANCE ORDER

Remove a fog light (see. The section Removal and installation of other devices of external lighting), separate the socket which was under it, remove a spring bracket and take out a lamp.

Lamp of the forward index of turn

 PERFORMANCE ORDER

  1. Remove the forward index of turn in collecting (see. Section Removal and installation of other devices of external lighting).
  1. Take out a lamp (1) index of turn from the boss (2) in the direction specified by an arrow.

Lamps of the back combined lamp

 PERFORMANCE ORDER

  1. Remove the lateral panel of furnish of a luggage compartment (see. Head Body).
  2. Turn and take out a cartridge of the corresponding lamp.
1 — a backing Lamp
2 — the turn Index
3 — the Back marker light, a back foggy lamp
4 — the Back marker light, a svetootrazhatel
5 — the Stoplight
  1. Turn and take out a lamp from the boss.

Lamps of illumination of registration plate

 PERFORMANCE ORDER

  1. Unclench a clamp on the right side and extend a lamp of illumination of registration plate.
  1. Take out a lamp.

Lamps of illumination of external handles of doors

 PERFORMANCE ORDER

  1. Remove door furnish (see. Head Body).
  1. Disconnect the central light source (1) from an arm (2), separate the socket (3) and disconnect an optical fiber (4) from the central light source.

The radius of a bend of optical fiber should not be less than 20 mm.


  1. Open a bayonetny lock of the central light source.
  1. Take out the filament lamp (1) of a reflector (2) and replace it.


«previous page
14.2.4. Removal and installation of devices of internal lighting
following page»
14.2.6. Replacement of lamps of devices of internal lighting