BMW 7_ая the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
5. Systems of cooling of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Kardanny and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
13.1. External equipment and body elements
13.2. Salon equipment
13.2.1. Removal and installation of window regulators
13.2.2. Removal and installation of furnish and sound insulation of a forward door
13.2.3. Removal and installation of furnish and sound insulation of a back door
13.2.4. Removal and installation of panels of furnish of racks of a body and ceiling
13.2.5. Removal and installation of furnish of the dashboard
13.2.6. Removal and shelf installation behind a back seat and shtorka of back glass
13.2.7. Removal and installation of overlays of thresholds of doors
13.2.8. Removal and installation of elements of furnish of a luggage compartment and its cover
13.2.9. Removal and installation of forward seats
13.2.10. Removal and installation of a back seat
13.2.11. Removal and installation of seat belts
13.2.12. Removal and installation of a cover of the top hatch
14. Onboard electric equipment
15. Electric equipment schemes




0c1943ba

13-2-4-snyatie-i-ustanovka-panelejj-otdelki-stoek-kuzova-i-potolka.html

13.2.4. Removal and installation of panels of furnish of racks of a body and ceiling

A rack

 PERFORMANCE ORDER

  1. On models with a safety cushion in A rack:
  • Remove a protective fringing on an overlay of a rack and take out a clip (1);
  • Turn out a bolt (1).

At installation check correctness of provision of a clip (2).

  1. Remove an overlay of a forward rack movement inside and up.
  1. Installation is made upside-down. Replace the damaged clamps and caps.
  1. On models with a safety cushion in A rack the soft uvula (1) cap (2) should be turned towards a safety cushion (3), otherwise the clip (4) can damage a pillow.

B rack, bottom section of furnish

 PERFORMANCE ORDER

  1. Remove overlays of thresholds of forward and back doors (see. Section Removal and installation of overlays of thresholds of doors).
  2. Move a seat to extreme forward situation.
  1. Partially remove a protective fringing from an overlay of an average rack. Wring out clamps of the bottom panel of furnish of an average rack movement inside (1) and remove the panel of furnish by movement down (2).
  1. Installation is made upside-down. Replace the damaged clamps and caps.

B rack, top section of furnish

 PERFORMANCE ORDER

  1. Remove the bottom panel of furnish of a rack of B.
  1. Turn out a bolt of fastening of a seat belt of forward sitting.
  1. Remove a protective fringing of the top section of furnish of an average rack. Wring out clamps of the bottom section of furnish of a rack of B movement inside (1) and remove it movement down (2).
  1. Installation is made upside-down. Replace the damaged clamps and caps.

Rack of C

 PERFORMANCE ORDER

  1. Disconnect a plafond of the back lamp, remove it movement up and separate the socket.
  1. On models with a safety cushion in a rack of C (with a badge 1) turn out screws (2) and remove facing (3) movement inside and up.
  1. On models without a safety cushion in a rack of C turn out bolts and remove facing by movement inside and up.
  1. At replacement of the panel of furnish remove a noise isolation (1) from the old panel and paste it on the new panel.

Ceiling

 PERFORMANCE ORDER

  1. Remove all top hand-rail and furnish of all racks of a body.
  2. Remove the right forward seat (see. Section Removal and installation of forward seats).
  3. Uncover the top hatch (see. Section Removal and installation of a cover of the top hatch Head Body)
  1. Remove a sun-protection peak and lamps (1) illumination of a cosmetic mirror. Separate sockets, remove slips from a support and the hinge and turn out screws. Slightly extend a wire and separate the illumination socket.
  1. Turn out bolts and remove a protective framework. At replacement if necessary replace nuts in ceiling furnish.
  1. Remove a plafond of the main salonny lamp and separate the socket.
  1. Pick up and take out a cap, separate the socket.
  1. Rearrange a back of the left forward sitting in extreme back situation.
  1. On models to 05.1997 g вып. pick up and take out clamps (1) with left and on the right side. Squeeze out ceiling furnish of metal pads movement back and remove it, shifting towards the right back door. On models from 05.1997 g вып. squeeze out ceiling furnish of metal pads movement back and remove, shifting towards the right back door.
  1. Installation is made upside-down. Insert the adaptation No. 51 4 000 into the basis of a covering of a ceiling and fix a sticky tape on a textile basis (2). On models with the block of connection of automobile phone, whenever possible, carry out over the block of connection of automobile phone (1).
  1. Press furnish (1) ceiling to the adaptation No. 51 4 000 movement up, move against the stop forward and fix. Remove the adaptation No. 51 4 000 and wipe back glass.
1 — ceiling Furnish
2 — the Sealing profile
3 — a glue Strip
4 — Back glass
5 — the Box of switches
6 — the aerial Basis
7 — the Aerial
8 — the Sticky tape on a textile basis


«previous page
13.2.3. Removal and installation of furnish and sound insulation of a back door
following page»
13.2.5. Removal and installation of furnish of the dashboard