BMW 7_ая the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
5. Systems of cooling of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Kardanny and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
13.1. External equipment and body elements
13.2. Salon equipment
13.2.1. Removal and installation of window regulators
13.2.2. Removal and installation of furnish and sound insulation of a forward door
13.2.3. Removal and installation of furnish and sound insulation of a back door
13.2.4. Removal and installation of panels of furnish of racks of a body and ceiling
13.2.5. Removal and installation of furnish of the dashboard
13.2.6. Removal and shelf installation behind a back seat and shtorka of back glass
13.2.7. Removal and installation of overlays of thresholds of doors
13.2.8. Removal and installation of elements of furnish of a luggage compartment and its cover
13.2.9. Removal and installation of forward seats
13.2.10. Removal and installation of a back seat
13.2.11. Removal and installation of seat belts
13.2.12. Removal and installation of a cover of the top hatch
14. Onboard electric equipment
15. Electric equipment schemes




0c1943ba

13-2-2-snyatie-i-ustanovka-otdelki-i-zvukoizolyacii-perednejj-dveri.html

13.2.2. Removal and installation of furnish and sound insulation of a forward door

Furnish

 PERFORMANCE ORDER

  1. Completely to lower door glass.
  1. Remove a lamp (1) illumination of a foot well and separate the socket. On models with memory of provisions of a seat of the driver take the corresponding switch (2) and separate the socket.
  1. Remove the switch (1) window regulators. Remove a cap (2) and turn out the screw.
  1. To remove a cap (1), pull out a clamp and remove the button (2) movement up.
  1. Liberate a door covering from clips on all perimeter.
  1. Extend a door covering from a clamp at doors up and push the internal handle (1) door via the furnish panel.
  1. Remove a clamp at doors.
  1. At replacement of the panel of furnish rearrange from the old panel on new various slips and the loudspeaker.
  2. Installation is made upside-down. Pay attention to the next moments.
  1. Check distance (A = 14.5 ± 1 mm) between a cap (1) and directing (2). If necessary remove the button and adjust position of the plug (3).
  1. Establish door furnish in a clamp at doors.
  1. Replace the damaged clips on door perimeter.
  2. Remove internal consolidation of glass not to damage it.

Sound insulation

 PERFORMANCE ORDER

  1. Remove the panel of furnish of a forward door.
  2. On models with a lateral safety cushion remove it.
  1. Separate the socket (1), turn out screws (2) and remove loudspeaker knot. Remove the handle of a drive of the lock of a forward door.
  1. Disconnect the central light source (1) from an arm (2), separate the socket (3) and disconnect an optical fiber (4) from the central light source.

The radius of a bend of optical fiber should not be less than 20 mm.


  1. Turn out screws (1) and remove an arm of the central light source (2).
  1. Unclench collars (1) on a plait of electroconducting (2) and separate sockets (4).
  1. Take clamps (1).
  1. In whole or in part separate the sealing roller (1) and remove or unbend sound insulation (2).
  1. Clear interfaced surfaces and lay a butyl cord in diameter of 6 mm on sound insulation and a door, heat up it the technical hair dryer, impose sound insulation and strongly press it on all perimeter with effort of 30 N/cm2.
  2. Further installation is made upside-down.


«previous page
13.2.1. Removal and installation of window regulators
following page»
13.2.3. Removal and installation of furnish and sound insulation of a back door