BMW 7_ая the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
5. Systems of cooling of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Kardanny and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
13.1. External equipment and body elements
13.1.1. Removal and installation of a forward wing
13.1.2. Removal, installation and adjustment of doors
13.1.3. Removal, installation and cowl adjustment, replacement of its racks
13.1.4. Removal, installation and adjustment of a cover of a luggage compartment, replacement of its components
13.1.5. Removal and installation of a front bumper and its components
13.1.6. Removal and installation of a rear bumper and its components
13.1.7. Replacement and adjustment of mobile glasses of doors
13.2. Salon equipment
14. Onboard electric equipment
15. Electric equipment schemes




0c1943ba

13-1-2-snyatie-ustanovka-i-regulirovka-dverejj.html

13.1.2. Removal, installation and adjustment of doors

Removal and installation

Lobbies and back doors act in film equally.


 PERFORMANCE ORDER

  1. Turn out bolts with a six-sided head above and below.
  1. Remove a protective cover. If the bracket is established, remove it. Establish the adaptation No. 51 2 010 and beat out a loop axis up.

At installation for driving in of a loop establish the adaptation No. 51 2 010 from above.

  1. Raise a door, take out it from a loop and lower on in advance prepared support about a threshold so that not to load door electroconducting.
  1. Turn out two screws of fastening of the socket of electroconducting. Extend the socket from a forward rack and separate it.
  1. Installation is made upside-down.
1 — the Bolt with a six-sided head
2 — the Motionless link of the top loop, fastens to a body
3 — a loop Axis
4 — the Mobile link of the top loop with the hinge plug, fastens to a door
5 — the Washer
6 — the Lock washer

Adjustment

Before adjustment of forward doors it is necessary to adjust back doors, i.e. back doors are adjusted to the welded back wings. In this case forward wings which fasten bolts, if necessary it is possible to adjust to forward doors. At adjustment the door should be completed with glass and the window regulator mechanism.

Sizes of gaps are specified in Specifications of Head the Body.


 PERFORMANCE ORDER

  1. Weaken fastening of the drummer of the lock.
  2. Completely remove tubular consolidation of a forward door.
  3. At installation of new doors establish rasporny washers between a door and loops. For preliminary adjustment establish on two washers, 1 mm everyone by thickness. Adjust a gap by means of the corresponding quantity of washers of necessary thickness.
  4. Lower glasses. At installation of new doors carry out preliminary adjustment of their situation on height: without the bottom dustproof overlay of a door the size of the bottom gap on all length should make about 20 mm. Adjustment is carried out by means of moving of loops.
  5. Check and if necessary adjust forward and back gaps (on a back door – only back) – they should be uniform and make 5 mm. Adjustment is carried out by means of moving of loops.
  6. At adjustment of a back door check its situation on height concerning a body. At adjustment of a forward door check a vzaimopolozheniye of forward and back doors on height. If necessary adjust the corresponding door on height as it is described below.
  1. Insert into the door lock a template No. 51 2 090.
  1. Weaken the screw (1). To weaken the screw (2) so that the drummer of the lock could be shifted insignificant effort of a hand.

Do not change clamp adjustment on depth (3).

  1. Raise the handle of a door and, holding her in this situation, close a door. The height and an inclination of the drummer of the lock is regulated on a template. Open a door and tighten screws (1 and 2 on an illustration).
  2. Check tubular consolidation of a door on absence of damages and if necessary replace it. To establish tubular consolidation of a door.
  3. Establish on a door the bottom dustproof slip.
  4. At installation of a forward door check a print of tubular consolidation on a surface of a door interfaced to it. For this purpose, being in the car at the closed door, insert thin (no more than 1 mm) a rectangular plastic subject (for example, a credit card) between tubular consolidation and a frame of a door and carry out this subject along an interfaced surface of consolidation and a frame, checking prilegany consolidations. In a ceiling zone between forward and central racks of a body the subject serving for check, should not be extended easily. If necessary replace consolidation or отрихтуйте a door fold which consolidation is put on.

The excessive rikhtovka of a fold will lead to increase in the effort necessary for closing of a door.



«previous page
13.1.1. Removal and installation of a forward wing
following page»
13.1.3. Removal, installation and cowl adjustment, replacement of its racks