BMW 7_ая the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
5. Systems of cooling of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Kardanny and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
12.1. General information, recommendations and security measures
12.2. Forward suspension bracket
12.3. Back suspension bracket
12.4. EDC system
12.5. Steering
12.5.1. Principle of work of GUR
12.5.2. Removal and installation of a steering wheel, block of a safety cushion and its contact ring
12.5.3. Removal and installation of casings of a steering column
12.5.4. Removal and installation of assembly of a steering column and sensor of an angle of rotation
12.5.5. Replacement of the lever of adjustment of a steering column
12.5.6. Removal and installation of the lock of ignition and blocking of a steering wheel
12.5.7. Removal and installation of the steering mechanism with GUR
12.5.8. Removal and installation of steering drafts, soshka and pendular lever
12.5.9. Removal and pump GUR installation
12.5.10. Corners of installation of wheels of the car - the general information
13. Body
14. Onboard electric equipment
15. Electric equipment schemes




0c1943ba

12-5-8-snyatie-i-ustanovka-rulevykh-tyag-soshki-i-mayatnikovogo-rychaga.html

12.5.8. Removal and installation of steering drafts, soshka and pendular lever

Soshka

At replacement of a soshka of a steering it is necessary to check height of its installation in relation to the pendular lever.


 PERFORMANCE ORDER

  1. Remove the steering mechanism (see. The section Removal and installation of the steering mechanism with GUR).
  2. Turn out tightening the screw (1), previously having noted the provision of an adjustable soshka of a steering on a shaft with gear sector.
1 — Tightening the screw
2 — Labels
  1. Installation is made upside-down. Get a steering soshka to the put label. Thus the label (2) should be in the middle of a shliyets of a soshka of a steering.

Replace самоконтрящуюся a nut.

Cross-section steering drafts

 PERFORMANCE ORDER

  1. To unscrew a nut and to remove cross-section steering draft by means of the adaptation No. 32 1 190.

At installation on a pin and in an opening there should not be greasing traces. Replace самоконтрящуюся a nut. If necessary keep knot from a provorachivaniye for an internal shestigrannik.


  1. Weaken tightening a bolt and turn out cross-section steering draft.
  1. Installation is made upside-down. Completely grease the adjusting coupling of draft with special greasing.
  2. Upon termination of works check and adjust corners of installation of forward wheels.

Average draft

 PERFORMANCE ORDER

  1. To remove protection of a case of the engine.
  2. Give a nut and disconnect draft from a soshka of a steering and from the pendular lever by means of a stripper No. 32 1 190.

At installation replace самоконтрящуюся a nut. If necessary keep knot from a provorachivaniye for an internal shestigrannik.

  1. Weaken the left and right tightening bolts (see an illustration) and turn out the adjusting coupling of draft at the left and on the right.
  2. Measure depth of installation of the adjusting coupling on the ends of old draft and screw the adjusting coupling on new draft on the corresponding depth from both parties.
  3. Installation is made upside-down. Grease the adjusting coupling of draft with special greasing.
  4. Upon termination of works check and adjust corners of installation of forward wheels.

Pendular lever

Details of knot of fastening of the pendular lever
1 — the Bolt
2 — the Pendular lever
3, 4 — Samokontryashchayasya a nut
5 — the Beam of the forward bridge

After replacement of the pendular lever it is necessary to adjust a steering soshka.


 PERFORMANCE ORDER

  1. Remove protection of a case of the engine.
  1. Give a nut and disconnect a spherical support by means of a stripper No. 32 1 190.

At installation on a pin and in an opening there should not be greasing traces. Replace самоконтрящуюся a nut. If necessary keep knot from a provorachivaniye for an internal shestigrannik.



«previous page
12.5.7. Removal and installation of the steering mechanism with GUR
following page»
12.5.9. Removal and pump GUR installation