BMW 7_ая the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and operation receptions
3. Settings and routine maintenance of the car
4. Engine
5. Systems of cooling of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Kardanny and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
12.1. General information, recommendations and security measures
12.2. Forward suspension bracket
12.3. Back suspension bracket
12.4. EDC system
12.5. Steering
12.5.1. Principle of work of GUR
12.5.2. Removal and installation of a steering wheel, block of a safety cushion and its contact ring
12.5.3. Removal and installation of casings of a steering column
12.5.4. Removal and installation of assembly of a steering column and sensor of an angle of rotation
12.5.5. Replacement of the lever of adjustment of a steering column
12.5.6. Removal and installation of the lock of ignition and blocking of a steering wheel
12.5.7. Removal and installation of the steering mechanism with GUR
12.5.8. Removal and installation of steering drafts, soshka and pendular lever
12.5.9. Removal and pump GUR installation
12.5.10. Corners of installation of wheels of the car - the general information
13. Body
14. Onboard electric equipment
15. Electric equipment schemes




0c1943ba

12-5-2-snyatie-i-ustanovka-rulevogo-kolesa-bloka-podushki-bezopasnosti.html

12.5.2. Removal and installation of a steering wheel, block of a safety cushion and its contact ring

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the storage battery.
  1. Turn out two bolts.

At installation do not press cables.

Models to 03.1999 g вып.

 PERFORMANCE ORDER

  1. Separate the electroconducting socket пиропатрона (1), the switch of a horn (2) and management buttons on a steering wheel (3). Remove the block of a safety cushion and postpone its party the face up.
  1. Establish a steering wheel in the provision of rectilinear movement (labels on a case of the steering mechanism and on the helmsman to a shaft should coincide).
  1. Turn out a bolt, note the provision of a steering wheel of rather steering shaft and remove a steering wheel.

At a reversing of a bolt the lock spring (F) which holds a contact ring in neutral situation therefore for the purpose of preservation of operability of a contact ring the steering wheel is not allowed to turn, works until then while the bolt will not be tightened.


  1. Installation of a steering wheel is made upside-down. The lock pin (1) should enter into a nest (2).
  1. If necessary adjust a contact ring. For this purpose press a spring (F on an illustration), define the neutral provision of a contact ring, having halved its complete revolution round an axis and release a spring. Pay attention to coincidence of labels (1).

Models from 03.1999 g вып.

 PERFORMANCE ORDER

  1. Separate sockets (1 and 2), remove the block of a safety cushion and postpone its party the face up.
  1. Establish a steering wheel in the situation corresponding to rectilinear movement of the car.
  1. Turn out a bolt and remove a steering wheel.
  1. Installation is made upside-down. Labels on a steering wheel and on the helmsman to a shaft should coincide. Lock pins (1) should enter into nests (2).

All models (replacement of a contact ring)

 PERFORMANCE ORDER

  1. At the removed steering wheel uncover and disconnect a wire going on weight.
  1. Turn out screws and remove a contact ring.

The lead (1) can be removed only after the contact ring will be fixed on a steering wheel, – compress both ends take out a lead.

  1. Installation is made upside-down.


«previous page
12.5.1. Principle of work of GUR
following page»
12.5.3. Removal and installation of casings of a steering column